A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

某型飞机前起落架收放作动筒耳环螺栓断裂故障分析

从断口理化分析、故障件检查、静强度、压杆失稳、出现裂纹后的剩余强度以及特殊受载情况等方面对耳环螺栓断裂故障进行了综合分析,找出了耳环螺栓断裂的原因。     

夹杂物特征参数对拉伸载荷下超高强度钢裂纹萌生与扩展的影响

采用扫描电镜原位观测的方法,动态跟踪观察拉伸载荷作用下航空发动机轴类超高强度钢MA250中不同形状和尺寸的TiN夹杂导致裂纹萌生与扩展的微观行为,从微观角度分析拉伸载荷作用下夹杂物的几何长轴与外加载荷方向成不同角度时裂纹的萌生方式.同时讨论TiN夹杂中第一条裂纹萌生所需的应力与夹杂物面积的关系.结果表明,夹杂物面积越大,第一条裂纹萌生所需的应力越小.     

美国MTS公司应用软件在测试上的应用

介绍了用美国ＭＴＳ公司的平面应变断裂韬度测试软件，对ＴＣ４合金进行ＫＩＣ测试的过程及结果。     

复合材料层板中就位横向拉伸强度的研究

本文利用弹性力学和断裂力学方法对纤维增强复合材料的横向拉伸强度进行了分析，其中考虑了９０度开裂层厚度和开裂邻层的约束效应的影响，推导出正交各向异性对称铺层中昨合就位横向拉伸强度的数学表达式，得出开裂层的厚度和约束邻层铺设角对就位横向拉伸强度都有影响的结论，理论计算与Ｆｌａｇｇｓ实验结果吻合较好。     

复杂系统的可靠性分析方法研究

本文对未来的运载器的复杂控制系统的可靠性建模、分配和预计的一般方法和程序及综合分析方法进行了讨论和研究。并简述了复杂系统的计算机辅助可靠性分析。     

门限自回归模型参数的局部正交设计寻优法

在采用点值图确定门限区间个数的基础上，对门自回归模型中门限值、滞后步长、各门限区间模型阶数，利用正交设计方法寻优，计算工作量锐减，却可得到精度较高的预报模型。     

Space weather: its effects and predictability

Terrestrial technology is now, and increasingly, sensitive to space weather. Most space weather is caused by solar storms and the resulting changes to the Earth's radiation environment and the magnetosphere. The Sun as the driver of space weather is under intense observation but remains to be adequately modelled. Recent spacecraft measurements are greatly improving models of solar activity, the interaction of the solar wind with the magnetosphere, and models of the radiation belts. In-situ data updates the basic magnetospheric model to provide specific details of high-energy electron flux at satellite orbits. Shock wave effects at the magnetopause can also be coarsely predicted. However, the specific geomagnetic effects at ground level depend on the calculation of magnetic and electric fields and further improvements are needed. New work on physical models is showing promise of raising geomagnetic and ionospheric predictability above the synoptic climatological level. This revised version was published online in August 2006 with corrections to the Cover Date.     

一种基于移步预测消除脉冲串扰的快速算法

以毫米波主被动复合探测器为工程应用背景,通过分析信号的特点,提出一种基于移步预测思想的快速算法来消除脉冲调制信号对被动通道信号的串扰。仿真分析和实验结果表明,该方法对改善信噪比效果明显,而且具有成本低、速度快和易于工程化实现的优点。